APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 160 / 379

Example value:

Normal / Tip over

Indication on Navigator always

Normal

, even when the sensor is inverted: disconnect the connector

and, with sensor inverted, check if there is continuity between the two PINS of the sensor: if there is no

continuity, replace the sensor; if there is, check the connector. If not OK, restore the cable harness; if

OK, check continuity to ground of PIN 1: if there is no continuity, restore the cable harness; if there is,

with key set to ON, check if there is 5V voltage at PIN 2. If there is not, check the Marelli control unit

connector (ENGINE connector PIN 8).

Indication on Navigator always

Tip over

: disconnect the connector and check if there is continuity

between the two PINS when the sensor is in vertical position: if there is continuity, replace the sensor;

if there is not, it means that, with key set to ON, there is no 5V voltage at PIN 2: restore the cable harness

whose pink/white cable will be shorted to ground

Electric fan circuit

ELECTRIC FAN CIRCUIT

Function

Radiator fan and coolant - Operation.

Operation / Operating principle

When the control unit detects a temperature of approx. 102 °C, it closes the fan control relay pickup

circuit to ground.

Level in electrical circuit diagram:

electric fan

Location:

•

the relay is located under the fuel tank, left side, first front relay (CHECK, however, the

identification of the relay with the colour of the cables).

Electrical characteristics:

•

relay normally open;

•

drive coil resistance 110 Ohm (+/- 10 %)

NAVIGATOR: STATUSES

Fan relay

Example value:

on/off

NAVIGATOR: ACTIVATION

Fan:

The fan relay (No. 44 in the wiring diagram, placed under fuel tank, left side, first front relay; CHECK,

however, the identification of the relay with the colour of the cables) is energised for 10 seconds. The

continuity of the wiring is necessary for correct activation: no error indications are displayed in case of

lack of activation.

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 160

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands