manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

The Aprilia Dorsoduro Factory ABS 2011 is a high-performance motorcycle built for thrilling rides. To ensure its optimal maintenance and care, download the free Service Station Manual from manualshive.com to access comprehensive instructions and guidelines. This manual is essential for any Dorsoduro owner seeking to maximize their riding experience.

Share
Download
background image

•

Unscrew and remove the anticlock-

wise nut fixing the rotor.

•

Remove the rotor.

•

Unscrew and remove the rotor control

gear fixing nut and act on the gear hex-

agonal insert.

•

Remove the rotor control gear.

•

From the cover inside to the outside,

remove the rotor control shaft with a

punch and a rubber hammer.

•

Use a screwdriver to remove the upper

part of the shaft and integrated seal as-

sembly as indicated.

CAUTION

BEFORE TIGHTENING THE 3 SCREWS, ENSURE THAT
THE TOOL IS PERFECTLY CENTRED WITH THE SEAL
AND THAT THE SCREWS ARE PERPENDICULAR TO THE
SURFACE OF THE SEAL ITSELF. TIGHTENING THE
SCREWS INCORRECTLY MAY DAMAGE THE OIL SEAL
UNDERNEATH THE WATER SEAL AND THE COVER IT-
SELF.

•

Fit the tool and use the specific punch

to make 3 holes in the integrated seal.

Specific tooling

020661Y

 

Water pump overall seal replacement

kit

Cooling system

DORSODURO FACTORY ABS

COOL SYS - 338

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

Xenith X1 Player'S Manual preview
X1
Brand: Xenith Pages: 17
hepco & becker Easyrack 6622520 01 01 Mounting Instructions preview
Easyrack 6622520 01 01
Brand: hepco & becker Pages: 4
LAZER Lugano User Manual preview
Lugano
Brand: LAZER Pages: 19
Kong MOUSE WORK Manual preview
MOUSE WORK
Brand: Kong Pages: 72
GAS GAS EC - 2006 User Manual preview
EC - 2006
Brand: GAS GAS Pages: 74
Takegawa 02-01-0284 Instruction Manual preview
02-01-0284
Brand: Takegawa Pages: 2
Zero SR/S Service Manual preview
SR/S
Brand: Zero Pages: 290
PUIG 0295 Mounting Instructions preview
0295
Brand: PUIG Pages: 2
Ducati Multistrada 620 Owner'S Manual preview
Multistrada 620
Brand: Ducati Pages: 382
Yamaha YZ250X 2022 Owner'S Service Manual preview
YZ250X 2022
Brand: Yamaha Pages: 276
SUOMY MX SPEED Manual preview
MX SPEED
Brand: SUOMY Pages: 26
hepco & becker 506998 00 01 Quick Start Manual preview
506998 00 01
Brand: hepco & becker Pages: 2
hepco & becker 610060 00 01 Manual preview
610060 00 01
Brand: hepco & becker Pages: 3
URAL Motorcycles cT 2022 Owner'S Manual preview
cT 2022
Brand: URAL Motorcycles Pages: 104
IBEX 10007032 Mounting Instruction preview
10007032
Brand: IBEX Pages: 3
Scott 2 Operation And Maintenance Instructions preview
2
Brand: Scott Pages: 22
SCORPION RKT-89 Fitting Instructions preview
RKT-89
Brand: SCORPION Pages: 2
SCORPION SIGS39 Installation Manual preview
SIGS39
Brand: SCORPION Pages: 15

Brands by name

Popular brands

Load more brands