APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 127 / 379

that is not functioning properly: if there is continuity, replace the control unit; if not, restore

the wiring.

NAVIGATOR: LOGIC ERRORS

Left side Throttle Grip Position (tracks A-B) P0154

- illogical signals.

Error cause

•

Two illogical voltage signals have been detected at PINS 42 and 40 of the VEHICLE con-

nector (tracks A-B)

Troubleshooting

•

Check the parameters of the left Throttle Grip Position Sensor - tracks A and B: if one of the

two values clearly deviates from 600-1400 mV, it means that this potentiometer is defective.

Check the throttle grip sensor connector and the control unit connector: if not OK, restore.

If OK, check that cable resistance between the throttle grip sensor connector and the control

unit is a few tenths of Ohm: if this is not the case, restore wiring. If the value is correct,

replace the complete throttle grip sensor.

Right side Throttle Grip Position (tracks C-D) P0155

- illogical signal.

Error cause

•

Two illogical voltage signals have been detected at PINS 30 and 44 of the ENGINE con-

nector (tracks A-B)

Troubleshooting

•

Check the parameters of the left Throttle Grip Position Sensor - tracks C and D: if one of the

two values clearly deviates from 600-1400 mV, it means that this potentiometer is defective.

Check the throttle grip sensor connector and the control unit connector: if not OK, restore.

If OK, check that cable resistance between the throttle grip sensor connector and the control

unit is a few tenths of Ohm: if this is not the case, restore wiring. If the value is correct,

replace the complete throttle grip sensor

Throttle Grip position P0156

- illogical signal.

Error cause

•

The value of the left side sensor (tracks A-B) does not coincide with the value of the right

side sensor (tracks C-D).

Troubleshooting

•

Replace the throttle grip sensor

RESET PROCEDURE

If the Marelli control unit or the throttle grip sensor is replaced, check the Handle self-learning with the

diagnosis instrument: once the check is completed, make sure that the Handle self-learning status

indicates: carried out.

CAUTION

THE TWO CONNECTORS WHICH GET TO THE THROTTLE GRIP SENSOR ARE ALIKE BUT THEY
SHOULD NEVER BE INVERTED. MARK OR CHECK THE CONNECTOR MARKING BEFORE RE-

DORSODURO FACTORY ABS

Electrical system

ELE SYS - 127

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands