APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 252 / 379

•

Position the plate together with the se-

lector.

•

Tighten the three screws fixing the

gear selector plate by applying Loctite

medium-strength.

•

Place the speed sensor with caution.

•

Tighten the speed sensor fixing screw.

•

Place the transmission control rod with

the washer.

•

Remove the grease off the primary pin-

ion tapered pins - crankshaft coupling

surfaces .

•

Position the crankshaft gear.

Engine

DORSODURO FACTORY ABS

ENG - 252

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands