APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 260 / 379

•

Fit the shim washer.

•

Fit the oil pump gear and fasten it

through appropriate screw with corre-

sponding washer.

•

By means of a commercial hook span-

ner, lock the pump and tighten the

screw to the prescribed torque.

NEW GENERATION PUMP INSTALLATION

•

Fit the oil pump in its seat.

Engine

DORSODURO FACTORY ABS

ENG - 260

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands