APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 78 / 379

•

Replace calibrated pads with a pad

thick enough to correct the valve clear-

ance previously detected.

•

List of calibrated break pads:

1. Calibrated pad 2.60

2. Calibrated pad 2.65

3. Calibrated pad 2.70

4. Calibrated pad 2.75

5. Calibrated pad 2.80

6. Calibrated pad 2.85

7. Calibrated pad 2.90

8. Calibrated pad 2.95

9. Calibrated pad 3.00

10.Calibrated pad 3.05

11.Calibrated pad 3.10

12.Calibrated pad 3.15

13.Calibrated pad 3.20

14.Calibrated pad 3.25

15.Calibrated pad 3.30

16.Calibrated pad 3.35

17.Calibrated pad 3.40

18.Calibrated pad 2.55

19.Calibrated pad 2.50

20.Calibrated pad 2.45

21.Calibrated pad 2.40

CAUTION

BEFORE REFITTING HEAD COVERS, CLEAN HEAD AND COVER SURFACES CAREFULLY.

•

Apply THREEBOND on the head cover

perimeter along the gasket housing.

Maintenance

DORSODURO FACTORY ABS

MAIN - 78

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands