APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 235 / 379

RANKCASE

pos.

Description

Type

Quantity

Torque

Notes

Engine speed sensor fixing screw

13 Nm (9.59 lbf ft)

Loctite 243

Screw fastening flywheel side /

clutch side crankcase halves

13 Nm (9.59 lbf ft)

Screw fastening flywheel side /

clutch side crankcase halves

29 Nm (21.39 lbf ft)

Special calibrated screw for gearbox

lubrication

18 Nm (13.28 lbf ft)

Splitting the crankcase halves

•

Fit the special tool, tightly fastening the

four screws securing the tool onto the

crankcase.

•

Undo and remove the crankshaft fas-

tener nut anticlockwise using the spe-

cial tool, retrieving the washer.

Specific tooling

020711Y

Engine pinion locking

DORSODURO FACTORY ABS

Engine

ENG - 235

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands