manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

The Aprilia Dorsoduro Factory ABS 2011 is a high-performance motorcycle built for thrilling rides. To ensure its optimal maintenance and care, download the free Service Station Manual from manualshive.com to access comprehensive instructions and guidelines. This manual is essential for any Dorsoduro owner seeking to maximize their riding experience.

Share
Download
background image

•

Check the filter box large connector and the throttle control unit connector: if not OK, restore;

if OK, check the continuity of the two lines from the filter box large connector to the VEHICLE

connector of the Marelli control unit: if not OK, restore the cable harness; if OK, check the

continuity of the two lines from the filter box large connector to the throttle control unit con-

nector: if not OK, restore the cable harness; if OK, replace the throttle control unit.

NAVIGATOR: LOGIC ERRORS

CAN Line to throttle control unit, U1706

 - no message update.

Error cause

•

No updated signal is received from the throttle control unit.

DORSODURO FACTORY ABS

Electrical system

ELE SYS - 169

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

Rally Pack 04910 Installation Instructions preview
04910
Brand: Rally Pack Pages: 2
ZARD ZUMA Fitting Manual preview
ZUMA
Brand: ZARD Pages: 2
GAS GAS TXT PRO - PART LIST CHASSIS 2003 Parts List preview
TXT PRO - PART LIST CHASSIS 2003
Brand: GAS GAS Pages: 36
MOTO GUZZI V 35 Owner'S Manual preview
V 35
Brand: MOTO GUZZI Pages: 61
SW-Motech ALK.00.733.15000/B Mounting Instructions preview
ALK.00.733.15000/B
Brand: SW-Motech Pages: 14
Memphis Shades 2320-0024 Mounting Instructions preview
2320-0024
Brand: Memphis Shades Pages: 2
SHERCO 2015 450 SEF-R Workshop Manual preview
2015 450 SEF-R
Brand: SHERCO Pages: 76
KTM Power Parts 60005099300 Information preview
60005099300
Brand: KTM Power Parts Pages: 12
SRC H-AFT18-15-01-SL Mounting Instructions preview
H-AFT18-15-01-SL
Brand: SRC Pages: 3
R&G ECC0289R Fitting Instructions Manual preview
ECC0289R
Brand: R&G Pages: 9
DYNATEK DDK1-11 Installation Manual preview
DDK1-11
Brand: DYNATEK Pages: 11
Suzuki 57100-05881 Installation Instructions Manual preview
57100-05881
Brand: Suzuki Pages: 80
National Cycle Quantum N50004 Installation Instructions preview
Quantum N50004
Brand: National Cycle Pages: 3
TM 2008 4 Stroke User Manual preview
2008 4 Stroke
Brand: TM Pages: 80
Starke TR-2503 Operation Manual preview
TR-2503
Brand: Starke Pages: 20
Wunderlich F 850 GS Manual preview
F 850 GS
Brand: Wunderlich Pages: 6
Panther EASY RIDER User Manual preview
EASY RIDER
Brand: Panther Pages: 36
Yamaha TN359 Quick Start Manual preview
TN359
Brand: Yamaha Pages: 4

Brands by name

Popular brands

Load more brands