APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 132 / 379

Troubleshooting

•

Check the pneumatic system between the pressure sensor and the socket to read pressure

on the throttle body; check that the intake manifold is in good conditions and the pressure

reading hole is clean.

Estimation error for front cylinder intake manifold pressure P0215

- pressure too high/pressure

too low.

Error cause

•

A substantial difference between the estimated pressure and the measured pressure has

been detected (for example, the pipe between sensor and throttle body is fully detached/

clogged or squashed).

Troubleshooting

•

Check the pneumatic system between the pressure sensor and the socket to read pressure

on the throttle body; check that the intake manifold is in good conditions and the pressure

reading hole is clean: there is an evident defect in the intake and pressure reading systems.

Estimation error for rear cylinder intake manifold pressure P0216

- pressure too high/pressure too

low.

Error cause

•

A substantial difference between the estimated pressure and the measured pressure has

been detected (for example, the pipe between sensor and throttle body is fully detached/

clogged or squashed).

Troubleshooting

•

Check the pneumatic system between the pressure sensor and the socket to read pressure

on the throttle body; check that the intake manifold is in good conditions and the pressure

reading hole is clean: there is an evident defect in the intake and pressure reading systems.

Pressure too low at front cylinder manifold error P0217

- signal not valid.

•

A small difference between the estimated pressure and the measured pressure has been

detected: the measured pressure is below the estimated one (for example, smeared throttle

body).

Troubleshooting

•

Check the pneumatic system between the pressure sensor and the socket to read pressure

on the throttle body; check that the intake manifold is in good conditions and the pressure

reading hole is clean.

Pressure too low at rear cylinder manifold error P0218

- signal not valid.

Error cause

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 132

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands