APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 159 / 379

Side stand

Example value:

up/down

Indication on Navigator

always down

: check the connector: if not OK, restore; if it is OK, disconnect

the two terminals from the sensor and check continuity to ground of PIN 1: if there is no continuity,

restore the cable harness; if there is, replace the sensor.

Indication on Navigator

always up

: disconnect the terminals from the sensor and check if there is

continuity between the two PINS, with stand down: if there is continuity, replace the sensor; if the circuit

is open, it means that the brown/green cable from sensor PIN 2 to ENGINE connector PIN 6 is short

circuit to ground: restore the cable harness.

Bank angle sensor

FALL SENSOR

Function

it tells the vehicle position to the control unit.

Operation / Operating principle

When the sensor is inverted, the circuit is closed

to ground: When the Marelli control unit detects

this ground connection, it does not enable start-up

or shuts off the engine.

Level in electrical circuit diagram:

Start-up ena-

bling switches.

Location:

•

on the vehicle: under the saddle

•

connector: near the sensor

Electrical characteristics:

•

Sensor in vertical position: open circuit

(resistance: 62 kOhm)

•

Sensor inverted: closed circuit (con-

tinuity)

Pin-out:

1. Ground connection

2. Voltage 5V

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

NAVIGATOR: PARAMETERS

Fall sensor

DORSODURO FACTORY ABS

Electrical system

ELE SYS - 159

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands