manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Share
Download
APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download Page 320

•

A. Cable continuity between PIN 8 of the ABS control unit connector and PIN 28 of the

instrument panel.

•

B. Check connectors - refer to the operations described in the chapter

If the previous checks are OK, the causes might be:

•

C. ABS control unit malfunction

•

D. Instrument panel malfunction

NOTE: to check the wheel speed sensor using the NAVIGATOR, follow the instructions given in

chapter "ELECTRICAL SYSTEM/CHECKS AND TESTS/SPEED SENSOR".

Using Navigator for the abs

ECU INFO screen page

This screen page shows general data regarding

the control unit, for example software type, map-

ping, control unit programming date

INFO ECU SCREEN PAGE

Characteristic

Value/example

Unit of

measure

ment

Notes

Vehicle manufacturing date
Chassis number
Software version
Vehicle code

Mana/Shiver/Dorso-

duro/Scarabeo

The vehicle code stored in the control unit is read.

Vehicle identification according to
the status of Pin 2 and 15 of the ABS
control unit connector

Mana/Shiver/Dorso-

duro/Scarabeo

The vehicle type (Mana/Shiver/Dorsoduro) is de-

fined according to the connection found for PIN 2
and PIN 15 of the ABS control unit connector. see

the following table

Braking system

DORSODURO FACTORY ABS

BRAK SYS - 320

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands