APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 154 / 379

•

Delete errors hindering throttle self-learning.

Rear throttle position error P0187

- misalignment between control and activation.

Error cause

•

The throttle mechanical control may be damaged.

Troubleshooting.

•

Replace the throttle body.

RESET PROCEDURE

If the Marelli control unit or the throttle body is replaced, do not start the engine within the 3 seconds

after the key is set to ON; during this time the control unit carries out the throttle self-learning process:

then make sure that the throttle self-learning status reads: carried out. If the indication is "Not carried

out", delete any possible errors present in the vehicle. Carry out Throttle self-learning process on the

adjustable parameters screen page (screwdriver and hammer), and check again that the throttle self-

learning status reads: carried out.

Engine oil pressure sensor

ENGINE OIL PRESSURE SENSOR

Function: it i

ndicates to the instrument panel if

there is enough oil pressure (0.5 + / - 0.2 bar (7.25

+ / - 2.9 PSI)) in the engine.

Operation / Operating principle:

normally closed

switch. With oil pressure above 0.5 + / -0.2 bar

(7.25 + / - 2.9 PSI), open circuit.

Location on the vehicle

: right side of the vehicle,

under the oil sump

Pin-out

: Voltage 5V

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 154

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands