APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 335 / 379

Circuit diagram

OOLING

SYSTEM

pos.

Description

Type

Quantity

Torque

Notes

Fan fastener screw

3 Nm (2.21 lbf ft)

Flanged TE screw fixing LH side ra-

diator to trellis frame and radiator

bracket to engine

M6x25

10 Nm (7.37 lbf ft)

Electric fan

•

Remove the radiator

•

Undo and remove the three screws

and collect the washers; remove the

electric fan.

See also

Removing the

radiator

DORSODURO FACTORY ABS

Cooling system

COOL SYS - 335

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands