APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download | Manualshive

Page: 305 / 379

background image

tions too. clearance should remain

constant at all wheel rotation phases.

•

If clearance is uniform but over 30 mm

(1.18 in) or below 25 mm (0.98 in), ad-

justment is necessary.

ADJUSTMENT

CAUTION

GET A SPECIFIC REAR SERVICE STAND (OPT) TO AD-
JUST THE CHAIN.

If you need to adjust chain tension after the check:

•

Place the vehicle on its rear service

stand (OPT).

•

Loosen the nut (1) completely.

•

Loosen both lock nuts (4).

•

Actuate on the adjuster screws (5) and

adjust the chain clearance checking

that the references (2-3) match on both

sides of the vehicle.

•

Tighten both lock nuts (4).

•

Tighten the nut (1).

•

Check chain clearance.

CAUTION

TO ENSURE THAT THE WHEEL IS CORRECTLY CEN-
TRED, THERE ARE FIXED REFERENCE MARKINGS (2-3)
INSIDE THE CHAIN TENSIONER SLIDER SEATS ON THE
SWINGARMS, IN FRONT OF THE WHEEL AXLE.

CHECKING THE CHAIN, THE PINION AND THE SPROCKET FOR WEAR

Furthermore, check the following parts and make sure the chain, the pinion and the sprocket do not

show:

•

damaged rollers;

•

loosened pins;

•

dry, rusty, flattened or jammed chain links;

•

excessive wear;

•

missing sealing rings;

•

excessively worn or damaged pinion or sprocket teeth.

IF THE CHAIN ROLLERS ARE DAMAGED, THE PINS ARE LOOSE AND/OR THE SEAL RINGS
ARE MISSING OR DAMAGED, THE WHOLE CHAIN UNIT (PINION, SPROCKET AND CHAIN)
SHOULD BE REPLACED.

DORSODURO FACTORY ABS

Chassis

CHAS - 305

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
303
304
305
306
307
...
»

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

Brand: B-PWR Pages: 12

Brand: GAS GAS Pages: 34

Brand: APRILIA Pages: 9

Brand: R&G Pages: 13

Brand: Memphis Shades Pages: 2

Brand: Yamaha Pages: 119

Brand: Yamaha Pages: 124

Brand: Yamaha Pages: 360

Brand: Yamaha Pages: 580

Brand: Yamaha Pages: 98

GRIZZLY 90 2020

Brand: Yamaha Pages: 132

Brand: Yamaha Pages: 132

Brand: Yamaha Pages: 166

Brand: Yamaha Pages: 452

Brand: Yamaha Pages: 132

Montana 7 Series

Brand: Garmin Pages: 24

Brand: Kask Pages: 24

EMPORIO ARMANI 946 2015

Brand: VESPA Pages: 416

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands