APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 125 / 379

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 42 of the VEHICLE con-

nector. If the circuit is open, shorted to negative: voltage equal to zero has been detected

at PIN 42 of the VEHICLE connector.

Troubleshooting

•

shorted to positive: check the value shown by the parameter of the left Throttle Grip Position

Sensor - track A: disconnect the left connector and see the value displayed by Navigator: if

the voltage does not vary, there is a short circuit in the cable wiring; replace the throttle grip

sensor if the voltage drops to zero.

•

if the circuit is open, shorted to negative: check the throttle grip sensor connector and the

Marelli control unit connector. If not OK, restore. If OK, check circuit continuity between the

two cable terminals. If not OK, restore; if OK, check the cable ground insulation (from the

throttle grip sensor connector or the control unit connector): if the cable is not ground insu-

lated, restore the wiring. If it is ground insulated, and with the key set to ON, check that there

is power supply for the potentiometer PIN A and that PIN C is connected to ground. If both

are correct, replace the throttle grip sensor; if not, check the continuity of the cable that is

not functioning properly: if there is continuity, replace the control unit; if not, restore the wiring

Left side Throttle Grip Position sensor - track B P0151-

short circuit to positive / open circuit, short

circuit to negative

Error cause

•

Voltage that is excessive / equal to zero has been detected at PIN 40 of the VEHICLE

connector.

Troubleshooting

•

short circuit to positive: check the value shown by the parameter of the left Throttle Grip

position Sensor track B: disconnect the left connector and see the value displayed by Nav-

igator: if the voltage does not vary, there is a short circuit in the cable wiring; replace the

throttle grip sensor if the voltage drops to zero.

•

if the circuit is open, shorted to negative: check the throttle grip sensor connector and the

Marelli control unit connector. If not OK, restore. If OK, check circuit continuity between the

two cable terminals. If not OK, restore; if OK, check the cable ground insulation (from the

throttle grip sensor connector or the control unit connector): if the cable is not ground insu-

lated, restore the wiring. If it is ground insulated, and with the switch key set to ON, check

that there is power supply for the potentiometer PIN D and that PIN F is connected to ground.

If both are correct, replace the throttle grip sensor; if not, check the continuity of the cable

that is not functioning properly: if there is continuity, replace the control unit; if not, restore

the wiring.

DORSODURO FACTORY ABS

Electrical system

ELE SYS - 125

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands