APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 264 / 379

Fuel pump

UEL

PUMP

pos.

Description

Type

Quantity

Torque

Notes

TEFL screw fastening fuel pump

M5x16

6 Nm (4.42 lbf ft)

Electrical characteristics:

•

Resistance: 0.7 +/- 0.2 Ohm

NAVIGATOR: ELECTRICAL ERRORS

Fuel pump relay control P0230

Example value:

shorted to positive / open circuit, shorted to negative.

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 62 of the VEHICLE con-

nector.

•

If the circuit is open, shorted to negative: voltage equal to zero has been detected at PIN 62

of the VEHICLE connector

Injection

Power supply

DORSODURO FACTORY ABS

P SUPP - 264

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands