manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

The Aprilia Dorsoduro Factory ABS 2011 is a high-performance motorcycle built for thrilling rides. To ensure its optimal maintenance and care, download the free Service Station Manual from manualshive.com to access comprehensive instructions and guidelines. This manual is essential for any Dorsoduro owner seeking to maximize their riding experience.

Share
Download
background image

•

Disconnect the fuel pump connector.

•

Remove the tank.

CAUTION

UPON REFITTING THE TANK, FOLLOW THE SAME STEPS BUT IN REVERSE ORDER. CONNECT
AGAIN THE FUEL PIPES AND THE FUEL PUMP CONNECTOR. REMEMBER TO SLIDE OFF THE
PIN PREVIOUSLY FITTED AND TO DRAW THE TANK BACKWARD AS MUCH AS POSSIBLE IN
ORDER TO FIT IT PROPERLY.

Instrument cluster support

•

Working on both sides, loosen the nuts

and screws and remove them.

•

Disconnect the connectors of arrow in-

dicators, headlamps, ignition key lock

and relay.

DORSODURO FACTORY ABS

Bodywork

BODYW - 365

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

ICON VARIANT Instruction Manual preview
VARIANT
Brand: ICON Pages: 8
hepco & becker 410999 00 01 Quick Start Manual preview
410999 00 01
Brand: hepco & becker Pages: 2
Ohlins HD 907 Mounting Instructions preview
HD 907
Brand: Ohlins Pages: 4
MV Agusta F4 750 Instructions Manual preview
F4 750
Brand: MV Agusta Pages: 36
Suzuki 1200 bandit Service Manual preview
1200 bandit
Brand: Suzuki Pages: 447
hepco & becker Minirack 6602533 01 01 Manual preview
Minirack 6602533 01 01
Brand: hepco & becker Pages: 4
Androware YC-06-C User Manual preview
YC-06-C
Brand: Androware Pages: 2
Two Brothers Racing 005-3860405-S1 Installation Instructions preview
005-3860405-S1
Brand: Two Brothers Racing Pages: 2
GAS GAS EX 250 2023 Owner'S Manual preview
EX 250 2023
Brand: GAS GAS Pages: 144
Baja motorsports DR70 Assembly Manual preview
DR70
Brand: Baja motorsports Pages: 20
DYNATEK D2K-HD2E User Instructions preview
D2K-HD2E
Brand: DYNATEK Pages: 8
Malossi DARK SMOKE SPORT Fitting Instructions preview
DARK SMOKE SPORT
Brand: Malossi Pages: 4
APRILIA SCARABEO 300 SPECIAL Manual preview
SCARABEO 300 SPECIAL
Brand: APRILIA Pages: 157
APRILIA PEGASO 650 IE - 2004 Manual preview
PEGASO 650 IE - 2004
Brand: APRILIA Pages: 96
APRILIA DORSODURO 750 - Brochure preview
DORSODURO 750 -
Brand: APRILIA Pages: 7
APRILIA ATLANTIC 500 sprint Manual preview
ATLANTIC 500 sprint
Brand: APRILIA Pages: 161
APRILIA DORSODURO 2007 Service Station Manual preview
DORSODURO 2007
Brand: APRILIA Pages: 302
R&G LP0127BK Fitting Instructions Manual preview
LP0127BK
Brand: R&G Pages: 11

Brands by name

Popular brands

Load more brands