manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

The Aprilia Dorsoduro Factory ABS 2011 is a high-performance motorcycle built for thrilling rides. To ensure its optimal maintenance and care, download the free Service Station Manual from manualshive.com to access comprehensive instructions and guidelines. This manual is essential for any Dorsoduro owner seeking to maximize their riding experience.

Share
Download
background image

km x 1,000

1

5

10

15

20

25

30

35

40

Light aiming

I

I

Fork oil seals

I

I

Flexible coupling ******

I

I

Tyres - pressure/wear (5)

I

I

I

I

I

I

I

I

I

Wheels

I

I

I

Bolts and nuts tightening

I

I

I

Suspensions and setting

I

I

I

Warning light indicating error on the instrument panel ****
Fuel pipes ***

I

I

Clutch wear

I

I

Break pad wear

I

I

I

I

I

I

I

I

I

Spark plug

At regular intervals, remove the spark plug and clean off any carbon deposits or replace as required.

CAUTION

ALWAYS REPLACE BOTH SPARK PLUGS EVEN IF ONLY ONE NEEDS REPLACING.

•

Remove the saddle.

•

Remove the lower air deflector.

•

Remove the side fairings.

In order to reach the spark plugs:

CAUTION

BEFORE CARRYING OUT THE FOLLOWING OPERATIONS AND IN ORDER TO AVOID BURNS,
LEAVE ENGINE AND SILENCER TO COOL OFF TO AMBIENT TEMPERATURE.

FRONT SPARK PLUG

•

Working on the left side of the vehicle,

undo and remove the screw.

Maintenance

DORSODURO FACTORY ABS

MAIN - 70

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

Insportline W-TEC AP-42 User Manual preview
W-TEC AP-42
Brand: Insportline Pages: 19
Memphis Shades 2320-0076 Mounting Instructions preview
2320-0076
Brand: Memphis Shades Pages: 2
Wolfman RTR4 Mounting Instructions preview
RTR4
Brand: Wolfman Pages: 3
Memphis Shades 2321-0054 Mounting Instructions preview
2321-0054
Brand: Memphis Shades Pages: 2
R&G CP0478 Fitting Instructions Manual preview
CP0478
Brand: R&G Pages: 13
Yamaha XJR1300(L) 99 Service Manual preview
XJR1300(L) 99
Brand: Yamaha Pages: 338
Yamaha R3 2021 Owner'S Manual preview
R3 2021
Brand: Yamaha Pages: 108
Yamaha R6 2023 Owner'S Manual preview
R6 2023
Brand: Yamaha Pages: 114
Yamaha PW50W 2007 Service Manual preview
PW50W 2007
Brand: Yamaha Pages: 168
Yamaha R15 2022 Service Manual preview
R15 2022
Brand: Yamaha Pages: 497
Yamaha R1 Series 2015 Service Manual preview
R1 Series 2015
Brand: Yamaha Pages: 704
Yamaha YZF-R15A Owner'S Manual preview
YZF-R15A
Brand: Yamaha Pages: 84
BMW F 650 GS Manual preview
F 650 GS
Brand: BMW Pages: 88
Brixton BX 125 2018 User Manual preview
BX 125 2018
Brand: Brixton Pages: 49
R&G FI0094BK Fitting Instructions preview
FI0094BK
Brand: R&G Pages: 4
R&G FI0062BK Fitting Instructions preview
FI0062BK
Brand: R&G Pages: 2
R&G FI0114BK Fitting Instructions Manual preview
FI0114BK
Brand: R&G Pages: 6
R&G FI0075BK Fitting Instructions preview
FI0075BK
Brand: R&G Pages: 4

Brands by name

Popular brands

Load more brands