manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Share
Download
APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download Page 189

Gearbox Selector Shaft

Removal

•

Place the left hand crankcase in a

press and extract the roller cage with

the specific tool.

NOTE

REPEAT THE SAME OPERATION FOR THE RIGHT HAND
CRANKCASE HALF.

Specific tooling

020724Y

 

Gear control rod roller cage punch

INSTALLATION

•

Place the left hand crankcase in a

press and install the roller cage with the

specific tool.

CAUTION

TO INSTALL THE ROLLER CAGE IN THE RIGHT HAND
CRANKCASE HALF, WORK WITH THE CYLINDER ON THE
SIDE OF THE 1 mm (*) STEP ON THE TOOL TURNED TO-
WARD THE ROLLER CAGE, WHEREAS TO INSTALL THE
CAGE IN THE LEFT HAND CRANKCASE HALF, USE THE
CYLINDER ON THE SIDE OF THE 2 mm (**) STEP ON THE
TOOL.

Specific tooling

020724Y

 

Gear control rod roller cage punch

Starter motor

DORSODURO FACTORY ABS

Engine

ENG - 189

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands