manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Share
Download
APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download Page 156

Neutral sensor

GEAR IN NEUTRAL SENSOR

Function

it tells the gear position to the control unit: if it is in

neutral or in gear.

Operation / Operating principle

for gear in neutral, the circuit is closed to ground

connection: then, via CAN, the control unit sends

the signal to the instrument panel which turns on

the neutral speed warning light.

Level in electrical circuit diagram:

Start-up ena-

bling switches

Location:

•

on the vehicle: left side of the vehicle,

near flywheel cover

•

connector: upper part of the flywheel

cover

Electrical characteristics:

•

gear in neutral: closed circuit (continu-

ity)

•

gear engaged: open circuit (infinite re-

sistance)

Pin-out:

1. Voltage 12V

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

NAVIGATOR: STATUSES

Gear in neutral

Example value:

yes/no

NAVIGATOR: NOTES

•

Indication on the instrument panel always gear engaged: check the correct position of the

cable terminals on the connector and the correct connection of the cables on the terminals.

If they are not correct, restore the cable harness; if correct, disconnect the connector and,

with gear in neutral, check continuity to terminal ground connection, sensor side: if there is

no continuity, replace the sensor (after checking cable continuity on the sensor side and the

correct mechanical position). If there is, check the correct position of the terminal on the

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 156

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands