APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download | Manualshive

Page: 241 / 379

background image

•

Remove the fuel vapour breather pipe

mounting plate.

CAUTION

DURING REASSEMBLY, REMEMBER TO FIT THE FUEL
VAPOUR BREATHER PIPE MOUNTING PLATE NEAR THE
PINION.

•

Rotate the engine and the engine

mounting into a horizontal position.

•

Undo and remove the pin, then retight-

en by one turn to give the crankcase

halves free play and verify tightness.

CAUTION

TAKE PARTICULAR CARE TO ENSURE THAT THE EN-
GINE AND ENGINE MOUNTING ARE STABLE AND EN-
SURE THAT THE ENGINE IS SECURELY FASTENED TO
THE MOUNTING PLATE.

•

Remove the two screws fastening the

mounting.

DORSODURO FACTORY ABS

Engine

ENG - 241

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
239
240
241
242
243
...
»

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

Brand: Bajaj Auto Pages: 38

Brand: Öhlins Pages: 2

Mechatronics 35007-01

Brand: Öhlins Pages: 4

McPherson Strut MIR 5H02

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 4

Brand: hepco & becker Pages: 7

Brand: SHERCO Pages: 102

XRM125 CFT125 2020

Brand: Honda Pages: 111

XV17ATMV(C) Road Star

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 118

Super Tenere ES 2022

Brand: Yamaha Pages: 132

Brand: Yamaha Pages: 282

Super Tenere ES 2020

Brand: Yamaha Pages: 130

Brand: Yamaha Pages: 211

Brand: Caberg Pages: 28

Brand: MSA Pages: 168

Brand: APRILIA Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands