APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download Page 277

Page: 277 / 379

•

Using the appropriate tool fasten the

fork in the vice.

Specific tooling

AP8140149

Protection for fitting operations

•

Operating on the upper screw, unload

the spring.

•

Loosen the cover without undoing it

completely.

•

Place the fork vertically locking it in a

vice by the specific tool.

•

Undo completely the cover.

Specific tooling

AP8140149

Protection for fitting operations

DORSODURO FACTORY ABS

Suspensions

SUSP - 277

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Brands by name

Popular brands