APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 115 / 379

Control unit

MARELLI CONTROL UNIT

Function

It controls the Ride by wire system, the injection/

ignition, the system safety checks and the self-di-

agnosis function.

Location:

•

left side, next to the engine

Connector location:

•

ENGINE connector: upper connector

with control unit on the vehicle; a letter

E is stamped on the control unit, to the

right of the connector.

•

VEHICLE connector: lower connector

with control unit on the vehicle; a letter

V is stamped on the control unit, to the

right of the connector.

Pin-out:

see the CONNECTORS section

NAVIGATOR: STATUSES

Engine status

Example value:

Indefinite_Key ON_Running engine_Stopped_Power latch_Power latch 2_Power latch

finished

Engine mode

Example value:

Indefinite_Start-up_Stable_Idle_Acceleration_Deceleration_Enters Cut Off_Cut

Off_Exits Cut Off

Immobilizer signal

Example value:

yes/no

Indicates whether the control unit has received the consent by the instrument panel regarding the im-

mobilizer: coded key or user code entered manually. Potential errors will be shown on the Instrument

Panel Errors screen page, on the DIAGNOSIS section of the instrument panel.

Start-up signal

Example value:

yes/no

Indicates whether the control unit will enable start-up when requested: in case the safety measures are

not respected (side stand, neutral sensor and clutch in correct position) or if the immobilizer does not

send the start-up consent to the control unit, the status is NO.

NAVIGATOR: FUEL INJECTION SYSTEM

PARAMETERS

DORSODURO FACTORY ABS

Electrical system

ELE SYS - 115

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands