APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 203 / 379

Checking the pusher plate

Check the pressure plate and the bearing for dam-

age and wear. If necessary, replace the parts.

Checking the clutch hub

Check the clutch hub for damage and wear that

may result in clutch irregular operation. If neces-

sary, replace the bell.

Checking the springs

•

Check the springs for damage and, if

necessary, replace the them all togeth-

er.

•

Measure the clutch spring length when

unloaded; if necessary, replace the

springs all together.

Clutch spring length when unloaded: 46.6 mm

(1.83 in)

DORSODURO FACTORY ABS

Engine

ENG - 203

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands