APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download | Manualshive

Page: 158 / 379

background image

•

Indication on Navigator always released: check the correct position of the cable terminals

on the connector and the correct connection of the cables on the terminals. If they are not

correct, restore the cable harness; if correct, disconnect the two terminals from the sensor

and, with key set to ON, check continuity to ground connection of PIN 2: if there is no con-

tinuity, restore the cable harness; if there is, replace the sensor

•

Indication on Navigator always pulled: disconnect the terminals from the sensor and check

if there is continuity between the two PINS, with clutch released: if there is continuity, replace

the sensor. If the circuit is open, it means that the brown/purple cable from sensor PIN 1 to

ENGINE connector PIN 50 is shorted to ground: restore the cable harness

Side stand sensor

SIDE STAND SENSOR

Function

It tells the side stand position to the control unit.

Operation / Operating principle

If the gear is engaged and the side stand is unfol-

ded, and therefore the circuit is open, the control

unit does not enable vehicle start-up or shuts off

the engine if it is rotating.

Level in electrical circuit diagram:

Start-up ena-

bling switches

Location:

•

on the vehicle: on the side stand

•

connector: left side, near the Marelli

control unit

Electrical characteristics:

•

Side Stand Up: closed circuit (continu-

ity)

•

Side Stand Down: open circuit (infinite

resistance)

Pin-out:

1. Ground connection

2. Voltage 12V

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

NAVIGATOR: STATUSES

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 158

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
156
157
158
159
160
...
»

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

Brand: 3M Pages: 26

Avenger 150 Street

Brand: Bajaj Auto Pages: 40

Brand: Caberg Pages: 3

Brand: Caberg Pages: 2

Brand: BMW Motorrad Pages: 143

Brand: Avenger Pages: 31

Brand: GAS GAS Pages: 26

GRIZZLY 90 2020

Brand: Yamaha Pages: 132

Brand: Yamaha Pages: 132

Brand: Yamaha Pages: 166

Brand: Yamaha Pages: 452

Brand: Yamaha Pages: 132

Outlander 6x6 450 XU+ 2022

Brand: Can-Am Pages: 226

Brand: BMW Pages: 241

Brand: DYNATEK Pages: 12

Brand: hepco & becker Pages: 2

Brand: hepco & becker Pages: 3

Competition Series

Brand: Vance and hines Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands