APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 75 / 379

Locking torques (N*m)

Oil drainage plug - M16x1.5

19 Nm (14.01 lbf ft)

•

Replace the oil filter.

•

Fill up to the right engine oil level by adding recommended engine oil.

See also

Engine

oil filter

Check

Engine oil filter

•

Drain the engine oil.

•

Remove the oil filter.

•

Fit a new engine oil filter.

•

Add engine oil up to the correct level.

CAUTION

NEVER REUSE AN OLD FILTER.

See also

Replacement

Air filter

•

Remove the fuel tank.

•

Disconnect the air temperature sensor.

•

Undo and remove the nine screws.

DORSODURO FACTORY ABS

Maintenance

MAIN - 75

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands