APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 99 / 379

TABLE L

First of all connect the light switches connectors

and the key switch inside the rubber cap and po-

sition the latter as in the figure, then the Demand

Master (BLUE tape) connector and then the "reg-

ulator" connector.

9. Regulator connector

10. Rubber cap that hosts light switch and key

switch connectors.

11. Demand 1 Master Connector

TABLE M

The clamp holds the cables going out from the light

switches and the immobilizer aerial cable going

out from the key switch.

4.5x180 (0.18x7.08) Clamp

TABLE N

2.5x160 (0.10x6.30) Clamp

TABLE O

12. Cable grommet

13. 2.5x98 (0.10x3.86) Clamps

14. 4.5x290 (0.18x11.42) Clamps

DORSODURO FACTORY ABS

Electrical system

ELE SYS - 99

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands