APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download | Manualshive

Page: 329 / 379

background image

The presence of air is signalled by the "sponginess" of the brake control and poor braking efficiency.

CONSIDERING THE DANGER FOR VEHICLE AND RIDER, IT IS STRICTLY NECESSARY, AFTER
REFITTING BRAKES AND RESTORING THE BREAKING SYSTEM TO THE REGULAR USE CON-
DITIONS, THAT THE HYDRAULIC CIRCUIT BE AIR PURGED.

NOTE

THE FOLLOWING OPERATIONS REFER TO ONLY ONE FRONT BRAKE CALLIPER BUT APPLY
TO BOTH CALLIPERS. THE VEHICLE MUST BE ON LEVEL GROUND TO BE PURGED. WHILE
PURGING THE HYDRAULIC SYSTEM, FILL THE RESERVOIR WITH THE NECESSARY QUANTITY
OF BRAKE FLUID. CHECK THAT, DURING THE OPERATION, THERE IS ALWAYS BRAKE FLUID
IN THE RESERVOIR.

•

Remove the rubber protection cover

from the bleed valve.

•

Insert the transparent plastic pipe in

the front brake calliper bleed valve and

slide the other end of this pipe in a con-

tainer to collect the fluid.

•

Remove the front brake oil reservoir

cap.

•

Quickly press and release the front

brake lever several times and then

keep it fully pressed.

•

Loosen the bleed valve 1/4 of a turn so

that the brake fluid flows into the con-

tainer. This will release the tension on

the brake lever and will make it reach

the end of stroke.

•

Close the bleed valve before the lever

reaches its end of stroke.

•

Repeat the operation until the fluid

draining into the container is air-bubble

free.

NOTE

WHILE PURGING THE HYDRAULIC SYSTEM, FILL THE
RESERVOIR WITH THE NECESSARY QUANTITY OF
BRAKE FLUID. CHECK THAT, DURING THE OPERATION,
THERE IS ALWAYS BRAKE FLUID IN THE RESERVOIR.

•

Screw the bleed valve and remove the pipe.

•

Top-up the reservoir until the correct brake fluid level is obtained.

•

Refit and block the front brake oil reservoir cap.

•

Refit the rubber protection cover.

DORSODURO FACTORY ABS

Braking system

BRAK SYS - 329

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
327
328
329
330
331
...
»

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

Brand: Sachs Bikes Pages: 83

Brand: R&G Pages: 12

Brand: Suzuki Pages: 206

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 88

TDM850'99 4TX-AE3

Brand: Yamaha Pages: 43

Brand: Yamaha Pages: 118

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 105

Brand: Yamaha Pages: 111

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 94

STRATOLINER XV19CTSC

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 72

Brand: Yamaha Pages: 74

Brand: Yamaha Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands