APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 215 / 379

pos.

Description

Type

Quantity

Torque

Notes

Special screw for fastening mobile /

fixed shoes

19 Nm (14.01 lbf ft)

Loctite 242

Cam tower / head fastener screws -

pre-tightening

4.90 - 6.86 Nm (3.61 -

5.06) lbf ft

Cam tower / head fastener screws -

tightening

9.81 - 12.75 Nm (7.24 -

9.40 lbf ft)

Camshaft retainer plate fastener

screw

torx M3

3 Nm (2.21 lbf ft)

Loctite 270

Removing the chain tensioner

•

Undo and remove the screw and col-

lect the washer and the internal spring.

•

Unscrew and remove the two screws.

•

Remove the chain tensioner and col-

lect the gasket.

Chain removal

•

Remove the chain tensioner.

•

Remove the main pinion.

•

Remove the movable chain slider and

release the fixed chain slider from the

clamp.

•

Unscrew and remove the pin of the tim-

ing chain intermediate gear paying at-

tention not to damage the O-ring.

•

Collect the washer.

DORSODURO FACTORY ABS

Engine

ENG - 215

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands