APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 146 / 379

Front / rear cylinder throttle correction

Example value:

0.0°

For example, if there is a hole in the intake manifold, the pressure read is different from the pressure

estimated by the control unit and the system tries to reach an "estimated" situation by opening the

throttle a little bit more; therefore, this parameter takes a value different from zero: an acceptable value

should be between -0.7º and +0.7º.

Front cylinder Limp home position / Rear cylinder Limp home position

Example value:

800 mV / 780 mV

Voltage stored in the control unit corresponding to the throttle Limp home position.

Front throttle lower position / Rear throttle lower position

Example value:

502 mV / 492 mV

Voltage stored in the control unit corresponding to the throttle mechanical minimum position.

NAVIGATOR: STATUSES

Throttle Self-learning

Example value:

carried out/not carried out

Indicates whether or not the self-acquisition process has been carried out through the diagnosis in-

strument.

NAVIGATOR: ACTIVATION

NAVIGATOR: ELECTRICAL ERRORS

Potentiometer 1 sensor, front throttle position P0120

Example value:

short circuit to positive / open circuit, short circuit to negative

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN A6 of the throttle control

unit. If the circuit is open, shorted to negative: voltage equal to zero has been detected at

PIN A6 of the throttle control unit.

Troubleshooting

•

shorted to positive: check the value shown by the parameter of the front throttle Potentiom-

eter 1 (voltage): disconnect the left connector and see the value displayed by Navigator: if

the voltage does not vary, there is a short circuit in the cable wiring; replace the throttle body

if the voltage drops to zero.

•

if the circuit is open, shorted to negative: check the throttle body connector and the throttle

valve connector. If not OK, restore; if everything is OK, check circuit continuity between the

two terminals. If not OK, restore the cable harness; if OK, check the circuit ground insulation

(from throttle sensor connector or control unit connector). If it is ground insulated, check that

there is power (+5 V) at the throttle body connector PIN 2, and that PIN 6 is connected to

ground. If both are correct, replace the throttle body.

Potentiometer 2 sensor, front throttle position P0122

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 146

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands