manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

The Aprilia Dorsoduro Factory ABS 2011 is a high-performance motorcycle built for thrilling rides. To ensure its optimal maintenance and care, download the free Service Station Manual from manualshive.com to access comprehensive instructions and guidelines. This manual is essential for any Dorsoduro owner seeking to maximize their riding experience.

Share
Download
background image

VEHICLE REAR SPEED SENSOR

FUNCTION:

To indicate the vehicle speed by read-

ing the rear wheel turning speed.

OPERATION / OPERATING PRINCIPLE:

Magne-

toresistive sensor: a square-wave pulse is gener-

ated with voltage approx. between 11.55 V and

11.25 V

WIRING DIAGRAM

 Level in wiring diagram: ABS.

REMOVAL

LOCATION ON THE VEHICLE:

on the swingarm,

right side, under the chain tension screw.

CONNECTOR LOCATION (if available):

 under

the saddle, right side.

PINS

•

PIN 1- Ground connection (yellow)

•

PIN 2 - Power supply voltage/Output

signal (yellow/brown)

NAVIGATOR

Parameters:

 Speed (km/h) - Vehicle speed.

ELECTRICAL ERRORS

Speed sensor

5DA0 electric malfunction:

Electrical fault in sensor or cable harness.

Troubleshooting:

Check the sensor connector and the ABS control unit connector. If they are not OK,

restore the connectors. If they are OK, check continuity of the yellow/brown cable between PIN 2 of the

sensor on the cable harness side and PIN 11 of the ABS control unit connector. If there is no continuity,

restore them. If there is, PIN 2 of the sensor on the cable harness side, with the sensor disconnected

and key set to ON, must have 12V voltage approximately: if there is no voltage, check PIN 2 for continuity

with the vehicle ground connection: if it is grounded, restore the cable harness. If OK, replace the control

unit. If PIN 2 has approx. 12 V, check continuity of the yellow cable between PIN 1 of the sensor on the

cable harness side and PIN 12 of the ABS control unit connector. If this is not OK, restore the cable

harness. If it is OK, replace the sensor.

LOGIC ERRORS

Speed sensor

5DA1 the signal works irregularly:

faulty sensor or signal interference.

Troubleshooting:

Check speed sensor retainer. If it is not OK, restore it. If it is OK, check if the tone

wheel is dirty, deformed or wrongly fixed. If any of this happens, replace the tone wheel. Otherwise,

replace the speed sensor.

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 120

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

TVS Apache RTR 160 HYPER EDGE 2015 Owner'S Manual preview
Apache RTR 160 HYPER EDGE 2015
Brand: TVS Pages: 60
hepco & becker 6617530 01 01 Mounting Instructions preview
6617530 01 01
Brand: hepco & becker Pages: 6
B-PWR SG4FB1-1 Instruction Manual preview
SG4FB1-1
Brand: B-PWR Pages: 13
Insportline W-TEC AP-42 User Manual preview
W-TEC AP-42
Brand: Insportline Pages: 19
SRC KTM390-14-01-SL Quick Start Manual preview
KTM390-14-01-SL
Brand: SRC Pages: 4
Honda VT250-FII Owner'S Manual preview
VT250-FII
Brand: Honda Pages: 190
R&G SS0059 Fitting Instructions Manual preview
SS0059
Brand: R&G Pages: 6
Suzuki VX800L Manual preview
VX800L
Brand: Suzuki Pages: 101
Yamaha YZF-R1 Assembly Instructions Manual preview
YZF-R1
Brand: Yamaha Pages: 15
Yamaha YW50A Owner'S Manual preview
YW50A
Brand: Yamaha Pages: 84
Shift Power C-T6 Installation Manual preview
C-T6
Brand: Shift Power Pages: 7
HYOSUNG RX 125 - Parts Catalog preview
RX 125 -
Brand: HYOSUNG Pages: 101
Bell Sports DialFit Owner'S Manual preview
DialFit
Brand: Bell Sports Pages: 2
Ram Mounts RMR-INS-B-309-7 Assembly Instructions preview
RMR-INS-B-309-7
Brand: Ram Mounts Pages: 2
Beta RR 125 ENDURO Owner'S Manual preview
RR 125 ENDURO
Brand: Beta Pages: 214
Beta Ark AC Service Manual preview
Ark AC
Brand: Beta Pages: 243
hepco & becker 7316514 00 01 Installation Instructions preview
7316514 00 01
Brand: hepco & becker Pages: 5
hepco & becker 730.4527 Assembling Instructions preview
730.4527
Brand: hepco & becker Pages: 6

Brands by name

Popular brands

Load more brands