APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 110 / 379

Check goal:

this control is to check that there are not any circuit interruptions nor excessive resistance,

for instance caused by rust, on the two terminals being inspected.

Tester:

set the tester on the "continuity" symbol and place the tester probes on the two circuit ends:

the tester emits a sound signal only if there is continuity; the tester can also be set to the Ohm symbol

to check that the circuit resistance is null or a few tenths of an Ohm.

CAUTION: THE CIRCUIT SHOULD NOT BE ENERGISED, OTHERWISE THE TEST IS IRRELE-

VANT.

GROUND CONNECTION check

Check goal:

this control is to check if a cable or a circuit is in contact with the vehicle ground (-)

connection.

Tester: set the tester on the "continuity" symbol and place one tester probe on the vehicle ground

connection (or on the battery - terminal) and the other probe on the cable being inspected: the tester

sends out a sound signal only if there is continuity. The tester can also be set to the Ohm symbol to

check that the circuit resistance is null or a few tenths of an Ohm.

CAUTION! IF THERE IS A GROUND CONNECTION COMING FROM THE CONTROL UNIT, MAKE

SURE THAT DURING THE TEST THE CONTROL UNIT IS GROUND CONNECTED TO THE CIR-

CUIT.

VOLTAGE check

Check goal:

this control is to check if a cable is energised, i.e. if it receives power supply from the

battery or the control unit.

Tester:

set the tester on the direct current symbol and place the tester red probe on the cable being

inspected and the black probe on the vehicle ground connection (or on the battery - terminal).

CAUTION

IN CASE OF TEMPORAL MALFUNCTIONING, CARRY OUT ALL DUE CHECKS LOOKING FOR
FAULT BY MOVING SLIGHTLY THE CABLE HARNESS BEING INSPECTED.

Dashboard

In case the EFI warning light turns on and the words SERVICE or URGENT SERVICE are shown on

the display, due to an error detected in the injection ECU, the malfunction indication will be deactivated

only after the vehicle has been used for a pre-set number of minutes of operation. However, even though

the malfunction is no longer present and the control unit considers the error no longer current but mem-

orised (MEM error indication on Navigator), the instrument panel may keep showing there is an error

present.

Diagnosis

An access code is required to enter this menu which controls the diagnosis function:

•

ENTER SERVICE CODE

This is a 5-digit code, fixed for each vehicle. For these vehicles, the code is:

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 110

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands