APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 362 / 379

UEL

TANK

pos.

Description

Type

Quantity

Torque

Notes

TCEI screw fastening filler cap flange

M5x16

3 Nm (2.21 lbf ft)

Rear TE screw fastening tank

M6x90

10 Nm (7.37 lbf ft)

CAUTION

DURING FUEL TANK LIFTING AND REPOSITIONING, BE CAREFUL SO AS NOT TO CRUSH/
BEND OR SLIDE OFF TANK BREATHERS FROM THE CORRESPONDING TUBE-GUIDES

LIFTING THE FUEL TANK

•

Remove the saddle.

•

Remove both side fairings.

•

Undo and remove the two tank front

screws.

See also

Side body panels

TANK REMOVAL

•

Undo and remove the rear screw.

•

Remove the rubber ring on the ignition

lock.

Bodywork

DORSODURO FACTORY ABS

BODYW - 362

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands