APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 138 / 379

sponds to -25%. In an open circuit, the lambda probe signal is too low. Therefore, the control unit takes

it as a lean combustion condition and will try to enrich it. The value read will be 0.75: once this correction

has been tried, the value shifts to 1.00 fixed and the Lambda probe error is signalled.

NAVIGATOR: STATUSES

Lambda

Example value:

Start-up_Lean_Rich_Fault due to rich value_Fault due to lean value

If the probe connector is removed (voltage almost equal to zero), the status is Fault due to lean value

Lambda check

Example value:

Open loop/Closed loop/Rich in closed loop/Lean in closed loop/enriched

Closed loop indicates that the control unit is using the lambda probe signal to keep the combustion as

close as possible to the stoichiometric value.

NAVIGATOR: ACTIVATION

Lambda probe heating

The auxiliary injection relay (No. 40 in the wiring diagram, placed under the fuel tank, right side, second

relay starting from the front; CHECK, however, the identification of the relay with the colour of the cables)

is energised and the heating circuit is closed to ground 5 times (pin 3 of the lambda probe connector).

The continuity of the wiring is necessary for correct activation: no error indications are displayed in case

of lack of activation.

NAVIGATOR: ELECTRICAL ERRORS

Lambda probe P0130

- Shorted to positive.

Error cause

•

Excessive voltage (battery voltage) has been detected at PIN 43 of the ENGINE connector.

Caution: the 'lambda probe' parameter is not the real value that is read; a recovery value is

displayed instead.

Troubleshooting

•

Shorted to positive: with key set to ON, disconnect the sensor connector and measure PIN

1 voltage on the cable harness side (grey cable): if there is voltage (5 or 12 V), restore the

cable harness; if there is not, replace the lambda probe.

Lambda probe heating P0135 -

shorted to positive / open circuit, shorted to negative.

Error cause

•

Shorted to positive: excessive voltage has been detected at PIN 32 of the ENGINE con-

nector.

•

If the circuit is open, shorted to negative: voltage equal to zero has been detected at PIN 32

of the ENGINE connector.

Troubleshooting

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 138

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands