APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 226 / 379

PISTON RINGS

•

Clean off any carbon deposits from the

grooves in the piston rings and from the

rings themselves.

•

Measure the piston ring side clearance

and replace the piston and the piston

rings all together if not complying with

specifications.

Piston ring side clearance:

Top ring (1st slot): 0.030 - 0.065 mm (0.0012 -

0.0026 in)

Intermediate ring (2nd slot): 0.020 - 0.055 mm

(0.0008 - 0.0022 in)

Oil scraper ring (3rd slot): 0.010 - 0.045 mm

(0.0004 - 0.0018 in)

•

Fit the piston ring to the cylinder.

•

Level the installed piston ring with the

piston crown.

•

Measure piston ring port and replace it

if not complying with specifications.

CAUTION

IT IS NOT POSSIBLE TO MEASURE THE GAP OF THE OIL
SCRAPER RING END: IF CLEARANCE IS EXCESSIVE, RE-
PLACE THE THREE PISTON RINGS.

Piston ring end gap:

Top ring: 0.25 - 0.40 mm (0.0079 - 0.0157 in)

Intermediate ring: 0.35 - 0.55 mm (0.0138 -

0.0216 in)

Oil scraper ring: 0.20 - 0.70 mm (0.0079 - 0.0276

in)

PIN

•

Clean off combustion residues from the piston crown and from the area above the top ring.

•

Check for cracks on the piston and for compression on the piston sliding surface (seizing);

Replace the piston if required.

CAUTION

SMALL STRIATIONS ON THE PISTON LINER ARE ADMISSIBLE.

Engine

DORSODURO FACTORY ABS

ENG - 226

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands