APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download Page 373

Page: 373 / 379

Specific operations for the vehicle

LEFT

•

Remove the left side chain protection

•

Fit a left bracket and a left chain pro-

tection; fasten then with a TEFL M8x35

mm screw at the top and with a TCEI

M8x35 mm screw at the bottom

NOTE

FINGER TIGHTEN THE SCREWS AND AFTERWARDS USE
THE SPECIFIC WRENCH

WARNING

OPERATIONS REQUIRED TO RENDER VEHICLE COMPLIANT WITH TWO SEATER TYPE AP-
PROVAL.

•

Remove the rubber cap.

DORSODURO FACTORY ABS

Pre-delivery

PRE DE - 373

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Brands by name

Popular brands