manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Share
Download
APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download Page 229

DISTRIBUTE Loctite 270 (high-strength) ON THE THREAD AND SCREW THE STUD BOLT ON
THE CRANKCASE UNTIL THEY PROTRUDE BY 137 mm (5.39 in), THEN MAKE SURE THE Loctite
HAS SET.

•

Insert a new cylinder base gasket, it

should be as thick as the gasket previ-

ously removed: 0.40 - 0.50 - 0.60 mm

(0.0157 - 0.0197 - 0.0236 in).

•

The silicone side should be facing the

crankcase.

CAUTION

IF THE ORIGINAL GASKET THICKNESS CANNOT BE
CHECKED OR SHOULD THE CYLINDER BE REPLACED,
REFER TO THE "BASE GASKET SELECTION" SECTION.

•

Before fitting the cylinder, place the

chain sliders and the timing chain on

the crankshaft; fit the timing chain on

the crankshaft from the base side.

NOTE

BEFORE FITTING THE CYLINDER, CAREFULLY BLOW
AIR INTO THE LUBRICATION DUCT AND LUBRICATE THE
CYLINDER LINER.

•

Insert the cylinder-head unit on the

stud bolts.

•

Working in a diagonal sequence and in

stages, screw the four nuts once the

stud bolt threads have been greased.

•

Screw the screw located outside the

cylinder.

DORSODURO FACTORY ABS

Engine

ENG - 229

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands