APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 231 / 379

•

Tighten the intermediate gear pin once

Loctite residues are thoroughly re-

moved and a high-strength threadlock

is applied on the thread.

•

Make sure that both timing chain slid-

ers are correctly fitted.

•

Refit the overhead camshafts following

the procedure described in the "Tim-

ing" section.

See also

Selecting the base gasket

Selecting the base gasket

•

Place the specific special tool on the

piston, which should have sealing rings

and be fitted on the connecting rod.

•

Lock the special tool with the clamp.

Specific tooling

AP8140302

tool for sealing ring fitting

•

Temporarily, fit the piston to the cylin-

der, without base or head gasket.

•

Remove the clamp from the sealing

ring locking tool.

•

Remove the special tool for locking the

connecting rod.

•

Fit a dial gauge on the specific tool.

•

Set the dial gauge to zero on a refer-

ence surface with a medium preload,

e.g. 5 mm (0.2 in). Keeping the zero

setting, fit the tool on the cylinder and

lock it with two nuts (10 Nm - 7.38 lb ft)

as shown in the figure.

Specific tooling

DORSODURO FACTORY ABS

Engine

ENG - 231

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands