APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download | Manualshive

Page: 140 / 379

background image

Injector

INJECTOR

Function

To supply the correct amount of petrol at the right

timing.

Operation / Operating principle

Injector coil is excited for the petrol passage to

open.

Level in electrical circuit diagram:

Coils and in-

jectors.

Location:

•

on the vehicle: inside the filter box

•

connector: on injector

Electrical characteristics:

•

14.8 Ohm +/- 5% (at 20 °C (68 °F))

Pin-out:

1. Supply: "+"

2. Ground connection

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

NAVIGATOR: PARAMETERS

Front cylinder injection time

Rear cylinder injection time

NAVIGATOR: ACTIVATION

Front injector

The auxiliary injection relay (No. 40 in the wiring diagram, placed under the fuel tank, right side, second

relay starting from the front; CHECK, however, the identification of the relay with the colour of the cables)

is energised for 5 seconds and the grey/green cable of the injector is closed to ground for 4 ms per

second. Disconnect the 4-way connector of the fuel pump to be able to hear the relay and injector

activation. The continuity of the wiring is necessary for correct activation: no error indications are dis-

played in case of lack of activation.

Rear injector

The auxiliary injection relay (No. 40 in the wiring diagram, placed under the fuel tank, right side, second

relay starting from the front; CHECK, however, the identification of the relay with the colour of the cables)

is energised for 5 seconds and the grey/red cable of the injector is closed to ground for 4 ms per second.

Disconnect the 4-way connector of the fuel pump to be able to hear the relay and injector activation.

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 140

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
138
139
140
141
142
...
»

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

651665 00 22-00-40

Brand: hepco & becker Pages: 5

Brand: Suzuki Pages: 206

Brand: Suzuki Pages: 440

Brand: Insportline Pages: 19

Brand: Yamaha Pages: 90

Brand: Yamaha Pages: 509

Brand: Yamaha Pages: 508

Brand: Yamaha Pages: 510

Brand: Yamaha Pages: 578

Brand: Yamaha Pages: 610

Brand: Yamaha Pages: 610

TT-R125(W) 2006

Brand: Yamaha Pages: 616

Brand: Yamaha Pages: 86

Brand: Öhlins Pages: 2

Brand: Magna Pages: 223

Brand: Yamaha Pages: 102

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands