manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Share
Download
APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download Page 118

THE FIRST TIME THE ENGINE IS STARTED AFTER RECONNECTING THE BATTERY LEADS,
WAIT 20 SECONDS BETWEEN THE MOMENT THE KEY IS SET TO "KEY ON" AND THE MOMENT
THE STARTER BUTTON CAN BE PUSHED.
THE ENGINE WILL NOT START IF START-UP IS ATTEMPTED BEFORE THE PRE-SET 20 SEC-
ONDS ELAPSE.

Speed sensor

VEHICLE FRONT SPEED SENSOR

FUNCTION:

To indicate the vehicle speed by read-

ing the front wheel turning speed.

OPERATION / OPERATING PRINCIPLE:

Magne-

toresistive sensor: a square-wave pulse is gener-

ated with voltage approx. between 11.55 V and

11.25 V

WIRING DIAGRAM

 Level in wiring diagram: ABS.

REMOVAL

LOCATION ON THE VEHICLE:

on the fork, right

stem, next to the brake calliper support.

CONNECTOR LOCATION (if available):

 under

the helmet compartment.

PINS

•

PIN 1- Ground connection (white)

•

PIN 2 - Power supply voltage/Output

signal (white/brown)

NAVIGATOR

Parameters:

 Speed (km/h) - Vehicle speed.

ELECTRICAL ERRORS

Speed sensor

5D90 electric malfunction:

 Electrical fault in sensor or cable harness.

Troubleshooting:

 Check the sensor connector and the ABS control unit connector. If they are not OK,

restore the connectors. If they are OK, check continuity of the white/brown cable between PIN 2 of the

sensor on the cable harness side and PIN 14 of the ABS control unit connector. If there is no continuity,

restore them. If there is, PIN 2 of the sensor on the cable harness side, with the sensor disconnected

and key set to ON, must have 12V voltage approximately: if there is no voltage, check PIN 2 for continuity

with the vehicle ground connection: if it is grounded, restore the cable harness. If OK, replace the control

unit. If PIN 2 has approx. 12 V, check the continuity of the white cable between PIN 1 of the sensor on

the cable harness side and PIN 13 of the ABS control unit connector. If there is no continuity, restore

the cable harness. If there is, replace the logic errors sensor.

LOGIC ERRORS

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 118

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands