APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 155 / 379

Instrument panel

Error DSB 07

Error cause

•

An oil sensor fault is signalled when,

with engine off, it is detected that the

sensor circuit is open. The test is per-

formed only once when the key is set

to ON. There is an error when the gen-

eral warning light turns on.

Troubleshooting

•

Check the sensor connector and the

instrument panel connector (PIN 17): if

they are not OK, restore. If OK, check

continuity of the purple cable between

the sensor connector and the instru-

ment panel connector PIN 17: if not

OK, restore the cable harness; if OK,

replace the sensor.

Error DSB 08

Error cause

•

An oil sensor fault is signalled when,

with engine running, it is detected that

the sensor circuit is closed. There is an

error when the general warning light

turns on.

Troubleshooting

•

Check if oil pressure is low with the

specific gauge.

DORSODURO FACTORY ABS

Electrical system

ELE SYS - 155

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands