manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

The Aprilia Dorsoduro Factory ABS 2011 is a high-performance motorcycle built for thrilling rides. To ensure its optimal maintenance and care, download the free Service Station Manual from manualshive.com to access comprehensive instructions and guidelines. This manual is essential for any Dorsoduro owner seeking to maximize their riding experience.

Share
Download
background image

Installing the chain tensioner

Refit the removed timing system chain tensioner

on the cylinder - head:

•

Fit the timing chain on the crankshaft

and on the intermediate gear.

•

Remove the screw and collect the

washer and the spring.

•

Fit the chain tensioner body on the cyl-

inder and insert a new paper gasket.

•

Tighten the two screws to the prescri-

bed torque.

•

Insert the spring and tighten the screw

together with the washer.

Cam timing

Timing

•

Rotate the crankshaft until the front cylinder piston reaches the top dead centre.

•

Lock the crankshaft with the specific special tool

Specific tooling

020720Y

 

Timing tool

Engine

DORSODURO FACTORY ABS

ENG - 218

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

Keis X900 Operating Instructions preview
X900
Brand: Keis Pages: 2
probrake SU10-5 Mounting Instruction preview
SU10-5
Brand: probrake Pages: 2
Parweld XR935H Instruction Manual preview
XR935H
Brand: Parweld Pages: 37
LAZER Mambo Evo PURE CARBON User Manual preview
Mambo Evo PURE CARBON
Brand: LAZER Pages: 13
OKBABY No shock Quick Start Manual preview
No shock
Brand: OKBABY Pages: 35
Takegawa Operation and Instruction Manua Operation And Instruction Manual preview
Operation and Instruction Manua
Brand: Takegawa Pages: 9
Honda Z125MA Manual preview
Z125MA
Brand: Honda Pages: 127
PMI Ventilator Instructions preview
Ventilator
Brand: PMI Pages: 2
Yamaha YBR125ESD Owner'S Manual preview
YBR125ESD
Brand: Yamaha Pages: 82
Yamaha YBR125 Custom Owner'S Manual preview
YBR125 Custom
Brand: Yamaha Pages: 84
Yamaha YBR125ED Owner'S Manual preview
YBR125ED
Brand: Yamaha Pages: 90
Yamaha YBR 125K Owner'S Manual preview
YBR 125K
Brand: Yamaha Pages: 83
Yamaha YZ250 2021 Owner'S Manual preview
YZ250 2021
Brand: Yamaha Pages: 148
Yamaha Y15ZR Owner'S Manual preview
Y15ZR
Brand: Yamaha Pages: 96
Yamaha Y16ZR 2021 Owner'S Manual preview
Y16ZR 2021
Brand: Yamaha Pages: 108
Yamaha YZ250F 2009 Owner'S Service Manual preview
YZ250F 2009
Brand: Yamaha Pages: 190
Yamaha yz250f A 2011 Owner'S Service Manual preview
yz250f A 2011
Brand: Yamaha Pages: 196
Yamaha yz250f 2012 Owner'S Service Manual preview
yz250f 2012
Brand: Yamaha Pages: 198

Brands by name

Popular brands

Load more brands