manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Share
Download
APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download Page 273

Checking the front wheel

FRONT WHEEL BEARINGS

Carry out the check with the bearings fitted on the wheel.

CHECK THAT ALL PARTS ARE IN GOOD CONDITION, ESPECIALLY THOSE LISTED AS FOL-
LOWS.

ROTATION CHECK

•

Manually rotate the inside ring of each bearing. Rotation must be constant, smooth and

noiseless.

If one or both bearings do not fall within the control parameters:

•

Replace both wheel bearings.

RADIAL AND AXIAL CLEARANCE CHECK

•

Check the radial and axial clearance.

Axial clearance: a minimum axial clearance is allowed.

Radial clearance: none.

If one or both bearings do not fall within the control parameters:

•

Replace both wheel bearings.

ALWAYS REPLACE BOTH BEARINGS.
ALWAYS REPLACE THE BEARINGS WITH OTHERS OF THE SAME TYPE.

GASKETS

•

Check that the gaskets are in good conditions; replace them if they show signs of damage

or excessive wear.

ALWAYS REPLACE BOTH GASKETS.
ALWAYS REPLACE THE GASKETS WITH OTHERS OF THE SAME TYPE.

wheel spindle

•

Use a dial gauge to check the wheel

spindle eccentricity. Replace the wheel

spindle if the eccentricity exceeds the

limit value.

Characteristic

Maximum eccentricity:

0.25 mm (0.0098 in)

DORSODURO FACTORY ABS

Suspensions

SUSP - 273

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands