APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 163 / 379

is in good conditions and the continuity of the grey/yellow cable between the sensor in question and

the VEHICLE connector PIN 26: if not OK, restore the cable harness; if OK, replace the Marelli control

unit.

Indication on Navigator always RUN: disconnect the connector and, with the switch set to STOP, check

if there is continuity between the two cables of the switch: if there is continuity, replace the switch; if

there is not, it means that, with key set to ON, the yellow/grey cable is shorted to positive: restore the

cable harness.

Throttle control unit

THROTTLE CONTROL UNIT

Function

It receives the throttles target position from the Marelli control unit and it moves them so that they reach

that target by reading their position through the potentiometers (2 per throttle body).

Level in wiring diagram:

throttle control unit

Location:

•

on the vehicle: inside the filter casing

•

connector: on the control unit

Pin-out:

see the CONNECTORS section

See also

Throttle control unit

Connectors

ECU

DORSODURO FACTORY ABS

Electrical system

ELE SYS - 163

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands