manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Share
Download
APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download Page 292

Get the suitable tool for the tightening of the ring

nut. Carry out the following operations:

- carry out a first tightening of the ring nut to the

indicated tightening torque for the settlement of the

steering package.

- turn the steering completely from both sides, for

several times.

Loosen the ring nut completely.

- carry out the final tightening of the ring nut to the

indicated tightening torque.

Specific tooling

020884Y

 

46 mm wrench for steering ring nut

S

TEERING

 

RING

 

NUT

pos.

Description

Type

Quantity

Torque

Notes

1

Headstock ring nut - pre-tightening

M25x1

1

30 Nm (22.13 lbf ft)

Steering package

settlement

1

Headstock ring nut - tightening

M25x1

1

12 Nm (8.85 lbf ft)

-

•

Fit the entire fork upper plate, adjusting

with short taps with a rubber hammer.

•

Scatter the nut thread with the specific

product and pre-fit it to the indicated

tightening torque.

Recommended products

LOCTITE® 243

 

Loctite adhesive to assemble

cylindrical pieces

Loctite adhesive to assemble cylindrical pieces

•

Tighten the fixing screws of the upper

plate to the prescribed tightening tor-

que.

Suspensions

DORSODURO FACTORY ABS

SUSP - 292

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands