APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 219 / 379

If necessary, remove the timing system gears from

the camshafts:

•

Place the camshaft with the timing sys-

tem gear on a vice and protect the

cams of the camshaft adequately.

•

Unscrew and remove the nut.

ANTICLOCKWISE NUT FOR BOTH REAR CYLINDER
SHAFTS, AN ANTICLOCKWISE ARROW HAS BEEN
PUNCHED ON IT.

•

Collect the washer.

•

Remove the timing system gear from

the camshaft.

•

Clean gears surfaces (camshaft cone and gear cone) with: "System MC 217 spray metal

cleaner".

•

Pre-fit the gear on the camshaft, so that it can turn freely.

•

Place the two camshafts in the head seats and align the two camshaft holes with the head

holes.

•

Align the clearance recovery gear to

the main timing system gear using the

specific tool.

Specific tooling

020718Y

Camshaft gear alignment pin

DORSODURO FACTORY ABS

Engine

ENG - 219

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands