APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 91 / 379

1. fall sensor

2. Intake air pressure sensor

3. Intake air temperature sensor

4. Instrument panel

5. Engine control unit

6. Headlamp

7. Start-up relay

8. Front ABS sensor

9. Starter motor

10.Engine speed sensor

11.Lambda probe

12.Rear ABS sensor

13.Coils

14.Main fuses

15.Hand grip position sensor

16.Main injection relay

17.Throttle control unit

18.Spark plugs

19.Taillight

20.Engine speed sensor - pick up

21.Gear in neutral sensor

22.ABS control unit (modulator)

23.Engine temperature sensor

24.Secondary fuses

CAUTION

A RELAY CANNOT BE IDENTIFIED BASED ONLY ON THE FOLLOWING INDICATIONS: THIS
SHOULD BE DONE ALSO IDENTIFYING THE COLOUR OF THE RELAY CABLES.

RELAY LAYOUT ON THE WIRING DIAGRAM AND ON THE VEHICLE

LIGHT LOGIC RELAY

•

Location on the wiring diagram: 7

•

Location on the vehicle: under the fuel tank, right side, first relay starting from the rear side.

START-UP RELAY

•

Location on the wiring diagram: 34

•

Location on the vehicle: under the fuel tank, left side, second relay starting from the front.

RETENTION RELAY

•

Location on the wiring diagram: 37

•

Location on the vehicle: under the fuel tank, right side, second relay starting from the front.

CONTROL RELAY

DORSODURO FACTORY ABS

Electrical system

ELE SYS - 91

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands