APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download | Manualshive

Page: 279 / 379

background image

•

Remove the spring paying attention to

drain the oil correctly.

•

Drain the oil into a container of suitable

capacity to collect fluids.

DO NOT DISPOSE OF OIL INTO THE ENVIRONMENT.
DISPOSE OF ENGINE OIL IN A SEALED CONTAINER AND
TAKE IT TO YOUR SUPPLIER OR TO THE NEAREST USED
OIL COLLECTION CENTRE.

•

Discharge the fork, remove the internal

dipstick of the pumping member pin (1)

and the washer (2).

•

Operate repeatedly on the pumping

member pin (3) so as to drain com-

pletely the oil from inside.

•

Slide off the dust scraper from the

sleeve using a screwdriver as a lever.

•

During this operation, pay attention not

to damage the sleeve rim.

DORSODURO FACTORY ABS

Suspensions

SUSP - 279

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
277
278
279
280
281
...
»

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

Brand: Idaho Pages: 72

Brand: KAYO MOTOR Pages: 84

Brand: Can-Am Pages: 16

Brand: Can-Am Pages: 254

Brand: National Cycle Pages: 3

Brand: Honda Pages: 102

Brand: SHERCO Pages: 76

Brand: Kabuto Pages: 6

Brand: GAS GAS Pages: 32

Brand: KC Pages: 32

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 96

X-MAX 400 ABS 2018

Brand: Yamaha Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands