manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

The Aprilia Dorsoduro Factory ABS 2011 is a high-performance motorcycle built for thrilling rides. To ensure its optimal maintenance and care, download the free Service Station Manual from manualshive.com to access comprehensive instructions and guidelines. This manual is essential for any Dorsoduro owner seeking to maximize their riding experience.

Share
Download
background image

5DA2 the signal decreases periodically:

 Possible tone wheel fault due to deformations or dirt; pos-

sible alterations on the wheel bearing surface. In very rare cases, abnormal tone wheel vibrations.

Troubleshooting:

 Check if the tone wheel is dirty, deformed or wrongly fixed. If the tone wheel is not

OK, replace it. If it is OK, check for possible faults in the wheel bearings and if it is not OK, replace the

bearings.

5DA3 no signal or speed measured too low in relation to the front wheel:

 Faulty sensor or missing

sensor/tone wheel. Or excessive distance between the sensor and the tone wheel or tone wheel with

wrong number of teeth.

Troubleshooting:

 Check that the speed sensor and the tone wheel are installed. If they are not, install

them. If they are, check the speed sensor retainer. If it is not OK, restore it. If it is, check if the tone

wheel has the correct number of teeth or if it is dirty, deformed or wrongly fixed. If it is not OK, replace

the tone wheel and if it is OK, replace the speed sensor.

5DA4 missing acceleration after pressure reduction:

 Faulty sensor or missing sensor/tone wheel

or excessive distance between the sensor and the tone wheel.

Troubleshooting:

 Check that the speed sensor and the tone wheel are installed. If they are not, install

them. If they are, check the speed sensor retainer. If it is not OK, restore it. If it is, check if the tone

wheel has the correct number of teeth or if it is dirty, deformed or wrongly fixed. If it is not OK, replace

the tone wheel and if it is OK, replace the speed sensor.

5DA5 excessive measured speed:

 Faulty sensor or tone wheel, or tone wheel with wrong number of

teeth or wrong tyre size.

Troubleshooting:

Check that the speed sensor and the tone wheel are installed. If they are not, install

them. If they are, check the speed sensor retainer. If it is not OK, restore it. If it is, check if the tone

wheel has the correct number of teeth or if it is dirty, deformed or wrongly fixed. If it is not OK, replace

the tone wheel and if it is OK, check that the tyre size is the correct one. If it is not OK, replace it. If it is

OK, check that the tyre pressure is the correct one. If it is not OK, restore it; if it is OK, replace the speed

sensor.

Engine rpm sensor

ENGINE SPEED SENSOR

Function

It informs crankshaft position and speed to the

Marelli control unit.

Operation / Operating principle

Inductive sensor: sinusoidal-type generated volt-

age; two teeth are missing on the flywheel for the

reference position.

DORSODURO FACTORY ABS

Electrical system

ELE SYS - 121

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

LSL 507T068A Fitting Instruction preview
507T068A
Brand: LSL Pages: 4
MSA F2 X-TREM Operating Manual preview
F2 X-TREM
Brand: MSA Pages: 163
GLOBBER 505-100 Manual preview
505-100
Brand: GLOBBER Pages: 72
Honda VT750CD ACE Electrical Repair And Modification preview
VT750CD ACE
Brand: Honda Pages: 25
KTM 450 SX-F 2019 Owner'S Manual preview
450 SX-F 2019
Brand: KTM Pages: 163
PUIG 21226 Mounting Instructions preview
21226
Brand: PUIG Pages: 6
Yamaha WOLVERINE R MAX 2021 Manual preview
WOLVERINE R MAX 2021
Brand: Yamaha Pages: 190
Yamaha WOLUERINE RMAX Owner'S Manual preview
WOLUERINE RMAX
Brand: Yamaha Pages: 194
Yamaha WOLVERINE RMAX2 2024 Owner'S Manual preview
WOLVERINE RMAX2 2024
Brand: Yamaha Pages: 196
Yamaha Vstar XVS650T 2004 Owner'S Manual preview
Vstar XVS650T 2004
Brand: Yamaha Pages: 101
Yamaha YZ85(Z) Owner'S Manual preview
YZ85(Z)
Brand: Yamaha Pages: 86
Yamaha YZ85 2013 Owner'S Manual preview
YZ85 2013
Brand: Yamaha Pages: 88
Yamaha TDM850'99 4TX-AE3 Service Manual preview
TDM850'99 4TX-AE3
Brand: Yamaha Pages: 43
Yamaha YZFR6Z(C) Owner'S Manual preview
YZFR6Z(C)
Brand: Yamaha Pages: 118
Yamaha TT-R125E Owner'S Manual preview
TT-R125E
Brand: Yamaha Pages: 92
Yamaha YZF600RT Owner'S Manual preview
YZF600RT
Brand: Yamaha Pages: 105
Yamaha YZF-R6T(C) Owner'S Manual preview
YZF-R6T(C)
Brand: Yamaha Pages: 111
Yamaha TT-R110E 2018 Owner'S Manual preview
TT-R110E 2018
Brand: Yamaha Pages: 88

Brands by name

Popular brands

Load more brands