APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 147 / 379

Example value:

short circuit to positive / open circuit, short circuit to negative

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN A5 of the throttle control

unit. If the circuit is open, shorted to negative: voltage equal to zero has been detected at

PIN A5 of the throttle control unit.

Troubleshooting

•

shorted to positive: check the value shown by the parameter of the front throttle Potentiom-

eter 2 (voltage): disconnect the left connector and see the value displayed by Navigator: if

the voltage does not vary, there is a short circuit in the cable wiring; replace the throttle body

if the voltage drops to zero.

•

if the circuit is open, shorted to negative: check the throttle body connector and the throttle

valve connector. If not OK, restore; if everything is OK, check circuit continuity between the

two terminals. If not OK, restore the cable harness; if OK, check the circuit ground insulation

(from throttle sensor connector or control unit connector). If it is ground insulated, check that

there is power (+5 V) at the throttle body connector PIN 2, and that PIN 6 is connected to

ground. If both are correct, replace the throttle body.

Potentiometer 1 sensor, rear throttle position P0125

Example value:

short circuit to positive / open circuit, short circuit to negative

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN B6 of the throttle control

unit. If the circuit is open, shorted to negative: voltage equal to zero has been detected at

PIN B6 of the throttle control unit.

Troubleshooting

•

shorted to positive: check the value shown by the parameter of the Rear throttle Potenti-

ometer 1 (voltage): disconnect the left connector and see the value displayed by Navigator:

if the voltage does not vary, there is a short circuit in the cable wiring; replace the throttle

body if the voltage drops to zero.

•

if the circuit is open, shorted to negative: check the throttle body connector and the throttle

valve connector. If not OK, restore; if everything is OK, check circuit continuity between the

two terminals. If not OK, restore the cable harness; if OK, check the circuit ground insulation

(from throttle sensor connector or control unit connector). If it is ground insulated, check that

there is power (+5 V) at the throttle body connector PIN 2, and that PIN 6 is connected to

ground. If both are correct, replace the throttle body.

Potentiometer 2 sensor, rear throttle position P0127

Example value:

short circuit to positive / open circuit, short circuit to negative

Error cause

DORSODURO FACTORY ABS

Electrical system

ELE SYS - 147

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands